Contents

Configuring user isolation· 1

About user isolation· 1

User isolation types· 1

SSID-based user isolation· 1

Enabling SSID-based user isolation· 3

User isolation configuration examples· 3

Example: Configuring SSID-based user isolation in centralized forwarding mode· 3

Example: Configuring SSID-based user isolation in local forwarding mode· 4

 

Configuring user isolation

About user isolation

The user isolation feature isolates packets for users that use the same SSID in the same VLAN or for users that are in the same VLAN. This feature improves user security, relieves the forwarding stress of the device, and reduces consumption of radio resources.

User isolation types

User isolation includes the following types:

·     SSID-based user isolation—Isolates wireless users that use the same SSID in the same VLAN.

·     VLAN-based user isolation—Isolates wired or wireless users in the same VLAN.

·     User group-based user isolation—Isolates wireless users in the same user group or different user groups.

SSID-based user isolation

SSID-based user isolation is applicable to both the local forwarding mode and the centralized forwarding mode.

When SSID-based user isolation is enabled for a service, the device isolates all wireless users that access the network through the service in the same VLAN.

User isolation mechanism in centralized forwarding mode

As shown in Figure 1, the AC centrally forwards the client traffic. Client 1 to Client 3 access the WLAN through AP 1 to AP 3 by using the service named service. Client 1 and Client 2 are in VLAN 100, and Client 3 is in VLAN 200. Enable user isolation on the AC for the service.

·     Client 1 sends broadcast or multicast packets in VLAN 100. When the AC receives the packets, it does not forward them to any APs in the WLAN. The AC forwards the packets only through the wired port to the switch.

·     Client 1 sends unicast packets to Client 2 in VLAN 100. When the AC receives the packets, it discards them instead of forwarding them to AP 2.

Figure 1 Packet forwarding path

‌

User isolation mechanism in local forwarding mode

This mechanism isolates wireless clients on the same AP.

As shown in Figure 2, the APs perform local traffic forwarding for clients. Client 1 to Client 4 access the WLAN through AP 1 to AP 3 by using the service named service. Client 1 to Client 3 are in VLAN 100, and Client 4 is in VLAN 200. Enable SSID-based user isolation on the service for AP 1.

·     Client 1 sends broadcast or multicast packets in VLAN 100.

¡     When AP 1 receives the packets, it does not forward them to Client 2 because user isolation is enabled. The AP forwards the packets only through the wired port to the wired devices in the same VLAN, including AP 2, AP 3, and the host.

¡     When AP 2 receives the packets, it forwards them to Client 3 because user isolation is disabled on AP 2.

¡     When AP 3 receives the packets, it does not forward them to Client 4 because Client 1 and Client 4 are in different VLANs.

·     Client 1 sends unicast packets to Client 2 in VLAN 100. When AP 1 receives the packets, it discards them instead of forwarding them to Client 2.

Figure 2 Packet forwarding path

‌

Enabling SSID-based user isolation

1.     Enter system view.

system-view

2.     Enter service template view.

wlan service-template service-template-name

3.     Enable SSID-based user isolation.

user-isolation enable

By default, SSID-based user isolation is disabled.

User isolation configuration examples

Example: Configuring SSID-based user isolation in centralized forwarding mode

Network configuration

As shown in Figure 3, Client 1 and Client 2 use the same SSID to access the Internet. The AC centrally forwards the client traffic.

Configure user isolation on the AC to isolate the clients from each other while providing Internet access for the clients.

Figure 3 Network diagram

‌

Procedure

# Configure Client 1 and Client 2 to access the Internet through service template service. For more information, see AP management and WLAN access in WLAN Configuration Guide. (Details not shown.)

# Enable SSID-based user isolation for service template service.

<AC> system-view

[AC] wlan service-template service

[AC-wlan-st-service] user-isolation enable

[AC-wlan-st-service] quit

Verifying the configuration

# Verify that Client 1 and Client 2 can use service service to access the Internet but cannot access each other. (Details not shown.)

Example: Configuring SSID-based user isolation in local forwarding mode

Network configuration

As shown in Figure 4, Client 1 and Client 2 use the same SSID to access the Internet. The APs perform local traffic forwarding.

Configure user isolation for AP 1 to isolate the clients from each other while providing Internet access for the clients.

Figure 4 Network diagram

‌

Procedure

# Configure Client 1 and Client 2 to access the Internet through service template service1. Configure the APs to perform local traffic forwarding for the clients. For more information, see AP management and WLAN access in WLAN Configuration Guide. (Details not shown.)

# Enable SSID-based user isolation for service template service1.

<AC> system-view

[AC] wlan service-template service1

[AC-wlan-st-service1] user-isolation enable

[AC-wlan-st-service1] quit

Verifying the configuration

# Verify that Client 1 and Client 2 can use service service1 to access the Internet but cannot access each other. (Details not shown.)