• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

H3C无线控制器典型配置案例集(V5)-6W114

目录

64-无线控制器 IPv6 VRRP热备管理AP典型配置举例(V5)

本章节下载 64-无线控制器 IPv6 VRRP热备管理AP典型配置举例(V5)  (237.51 KB)

64-无线控制器 IPv6 VRRP热备管理AP典型配置举例(V5)

无线控制器IPv6 VRRP热备管理AP的IPv6典型配置举例(V5)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

资料版本:6W114-20210416

 

Copyright © 2008-2021 新华三技术有限公司 版权所有,保留一切权利。

非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部,并不得以任何形式传播。

除新华三技术有限公司的商标外,本手册中出现的其它公司的商标、产品标识及商品名称,由各自权利人拥有。

本文档中的信息可能变动,恕不另行通知。



1  简介

本文档介绍了无线控制器VRRP热备管理AP的IPv6典型配置举例。

2  配置前提

本文档不严格与具体软、硬件版本对应,如果使用过程中与产品实际情况有差异,请参考相关产品手册,或以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证,配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置,为了保证配置效果,请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解WLAN接入、VRRP热备等特性。

3  配置举例

3.1  组网需求

图1所示,为了提高网络中AC的可靠性,现要求使用VRRP热备功能,将AC 1和AC 2组成一台虚拟AC,为Client提供无线接入服务。具体要求如下:

·     AC 1正常工作的情况下,Client通过AC 1访问网络。

·     当AC 1发生故障时,Client切换至AC 2上,保证业务流量在切换过程中不会中断。

图1 VRRP热备管理AP的IPv6典型组网图

 

3.2  配置思路

·     为了让AC 1成为VRRP备份组中的Master,需要为AC 1配置较高的优先级。

·     为了避免VRRP备份组中的角色频繁发生变化,可以配置一定的抢占延迟时间。

·     当备份组中的角色发生变化时,为了保证网络流量不会中断,需要在AC 1和AC 2之间建立IACTP隧道,并通过AP信息备份以及Client备份功能,使AC之间可以同步备份AP和Client的信息。

3.3  配置注意事项

·     两台AC需保证WLAN相关的特性配置一致,否则可能出现备份失败等问题。

·     配置AP的序列号时请确保该序列号与AP唯一对应,AP的序列号可以通过AP设备背面的标签获取。

·     需要确保在完成VRRP配置、IACTP隧道、开启客户端信息备份功能后,再开启AP信息备份功能。

·     需要在配置IACTP隧道的源IPv6地址后才可以开启隧道。

3.4  配置步骤

3.4.1  AC 1的配置

(1)     配置AC 1的接口

# 全局使能IPv6功能。

<AC1> system-view

[AC1] ipv6

# 创建VLAN 100及其对应的VLAN接口,并为该接口配置IPv6地址。AC 1将使用该接口的IPv6地址与AP建立LWAPP隧道,同时用于与AC 2建立VRRP备份组和IACTP隧道。

[AC1] vlan 100

[AC1-vlan100] quit

[AC1] interface vlan-interface 100

[AC1-Vlan-interface100] ipv6 address fe80::1 link-local

[AC1-Vlan-interface100] ipv6 address 3001::1 96

[AC1-Vlan-interface100] quit

# 创建VLAN 200作为WLAN-ESS接口的缺省VLAN,同时作为Client接入的业务VLAN,并为该接口配置IP地址。

[AC1] vlan 200

[AC1-vlan200] quit

[AC1] interface vlan-interface 200

[AC1-Vlan-interface200] ipv6 address 3002::1 96

[AC1-Vlan-interface200] quit

# 配置AC 1与Switch相连的GigabitEthernet1/0/1接口链路类型为Trunk,PVID为100,允许VLAN 100和VLAN 200的报文通过。

[AC1] interface gigabitethernet 1/0/1

[AC1-GigabitEthernet1/0/1] port link-type trunk

[AC1-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC1-GigabitEthernet1/0/1] port trunk pvid vlan 100

[AC1-GigabitEthernet1/0/1] quit

# 创建WLAN-ESS 1接口

[AC1] interface wlan-ess 1

# 配置WLAN-ESS 1接口链路类型为Hybrid。

[AC1-WLAN-ESS1] port link-type hybrid

# 配置当前Hybrid端口的PVIDVLAN 200,允许VLAN 200不带tag通过。

[AC1-WLAN-ESS1] port hybrid vlan 200 untagged

[AC1-WLAN-ESS1] port hybrid pvid vlan 200

# 在Hybrid端口上使能MAC VLAN功能。

[AC1-WLAN-ESS1] mac-vlan enable

[AC1-WLAN-ESS1] quit

(2)     配置VRRP功能

# 创建VRRP备份组1,并配置备份组1的虚拟IPv6地址为FE80::10和3001::100。

[AC1] interface vlan-interface 100

[AC1-Vlan-interface100] vrrp ipv6 vrid 1 virtual-ip fe80::10 link-local

[AC1-Vlan-interface100] vrrp ipv6 vrid 1 virtual-ip 3001::100

# 设置AC 1在备份组1中的优先级为110。

[AC1-Vlan-interface100] vrrp ipv6 vrid 1 priority 110

# 设置AC 1工作在抢占模式,抢占延迟时间为6秒。

[AC1-Vlan-interface100] vrrp ipv6 vrid 1 preempt-mode timer delay 6

# 配置允许发布RA消息。

[AC1-Vlan-interface100] undo ipv6 nd ra halt

[AC1-Vlan-interface100] quit

(3)     配置IACTP隧道

# 创建IACTP隧道1,并进入其视图。

[AC1] wlan mobility-group 1

# 配置IACTP隧道1的隧道类型为iactp6

[AC1-wlan-mg-1] mobility-tunnel iactp6

# 配置IACTP隧道1的源IPv6地址为AC 1的IPv6地址3001::1。

[AC1-wlan-mg-1] source ipv6 3001::1

# 配置IACTP隧道1的成员IPv6地址为AC 2的IPv6地址3001::2。

[AC1-wlan-mg-1] member ipv6 3001::2

# 开启IACTP隧道。

[AC1-wlan-mg-1] mobility-group enable

[AC1-wlan-mg-1] quit

# 开启客户端信息备份功能。

[AC1] wlan backup-client enable

# 设置AC 1的备份AC为AC 2。

[AC1] wlan backup-ac ipv6 3001::2

(4)     配置无线服务

# 创建clear类型的服务模板1。

[AC1] wlan service-template 1 clear

# 设置当前服务模板的SSID为service。

[AC1-wlan-st-1] ssid service

# 将WLAN-ESS 1接口绑定到服务模板1。

[AC1-wlan-st-1] bind wlan-ess 1

# 启用无线服务。

[AC1-wlan-st-1] service-template enable

[AC1-wlan-st-1] quit

(5)     配置AP

# 创建AP的管理模板,名称为testap,型号名称选择WA2620E-AGN。

[AC1] wlan ap testap model WA2620E-AGN

# 设置AP的序列号为21023529G007C000020。

[AC1-wlan-ap-testap] serial-id 21023529G007C000020

# 进入radio 2射频视图。

[AC1-wlan-ap-testap] radio 2

# 将在AC上配置clear类型的服务模板1与射频2进行关联。

[AC1-wlan-ap-testap-radio-2] service-template 1

# 使能AP的radio 2。

[AC1-wlan-ap-testap-radio-2] radio enable

[AC1-wlan-ap-testap-radio-2] return

3.4.2  AC 2的配置

(1)     配置AC 2的接口

# 全局使能IPv6功能。

<AC2> system-view

[AC2] ipv6

# 创建VLAN 100及其对应的VLAN接口,并为该接口配置IPv6地址。AC 2将使用该接口的IPv6地址与AP建立LWAPP隧道,同时用于与AC 1建立VRRP备份组和IACTP隧道。

[AC2] vlan 100

[AC2-vlan100] quit

[AC2] interface vlan-interface 100

[AC2-Vlan-interface100] ipv6 address fe80::2 link-local

[AC2-Vlan-interface100] ipv6 address 3001::2 96

[AC2-Vlan-interface100] quit

# 创建VLAN 200作为WLAN-ESS接口的缺省VLAN,同时作为Client接入的业务VLAN,并为该接口配置IP地址。

[AC2] vlan 200

[AC2-vlan200] quit

[AC2] interface vlan-interface 200

[AC2-Vlan-interface200] ipv6 address 3002::2 96

[AC2-Vlan-interface200] quit

# 配置AC 2与Switch相连的GigabitEthernet1/0/1接口链路类型为Trunk,PVID为100,允许VLAN 100和VLAN 200的报文通过。

[AC2] interface gigabitethernet 1/0/1

[AC2-GigabitEthernet1/0/1] port link-type trunk

[AC2-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC2-GigabitEthernet1/0/1] port trunk pvid vlan 100

[AC2-GigabitEthernet1/0/1] quit

# 创建WLAN-ESS 1接口

[AC2] interface wlan-ess 1

# 配置WLAN-ESS 1接口链路类型为Hybrid。

[AC2-WLAN-ESS1] port link-type hybrid

# 配置当前Hybrid端口的PVIDVLAN 200,允许VLAN 200不带tag通过。

[AC2-WLAN-ESS1] port hybrid vlan 200 untagged

[AC2-WLAN-ESS1] port hybrid pvid vlan 200

# 在Hybrid端口上使能MAC VLAN功能。

[AC2-WLAN-ESS1] mac-vlan enable

[AC2-WLAN-ESS1] quit

(2)     配置VRRP

# 创建VRRP备份组1,并配置备份组1的虚拟IPv6地址为FE80::10和3001::100,AC 2在备份组1中的优先级取缺省值100。

[AC2] interface vlan-interface 100

[AC2-Vlan-interface100] vrrp ipv6 vrid 1 virtual-ip fe80::10 link-local

[AC2-Vlan-interface100] vrrp ipv6 vrid 1 virtual-ip 3001::100

# 设置AC 2工作在抢占方式,抢占延迟时间为6秒。

[AC2-Vlan-interface100] vrrp ipv6 vrid 1 preempt-mode timer delay 6

# 配置允许发布RA消息。

[AC2-Vlan-interface100] undo ipv6 nd ra halt

[AC2-Vlan-interface100] quit

(3)     配置IACTP隧道

# 创建IACTP隧道1,并进入其视图。

[AC2] wlan mobility-group 1

# 配置IACTP隧道1的隧道类型为iactp6

[AC2-wlan-mg-1] mobility-tunnel iactp6

# 配置IACTP隧道1的源IPv6地址为AC 2的IP地址3001::2。

[AC2-wlan-mg-1] source ipv6 3001::2

# 配置配置IACTP隧道1的成员IPv6地址为AC 1的IPv6地址3001::1。

[AC2-wlan-mg-1] member ipv6 3001::1

# 开启IACTP隧道。

[AC2-wlan-mg-1] mobility-group enable

[AC2-wlan-mg-1] quit

# 开启客户端信息备份功能。

[AC2] wlan backup-client enable

# 设置AC 2的备份AC为AC 1。

[AC2] wlan backup-ac ipv6 3001::1

(4)     配置无线服务

# 创建clear类型的服务模板1。

[AC2] wlan service-template 1 clear

# 设置当前服务模板的SSID为service。

[AC2-wlan-st-1] ssid service

# 将WLAN-ESS 1接口绑定到服务模板1。

[AC2-wlan-st-1] bind wlan-ess 1

# 启用无线服务。

[AC2-wlan-st-1] service-template enable

[AC2-wlan-st-1] quit

(5)     配置AP

# 创建AP的管理模板,名称为testap,型号名称选择WA2620E-AGN。

[AC2] wlan ap testap model WA2620E-AGN

# 设置AP的序列号为21023529G007C000020。

[AC2-wlan-ap-testap] serial-id 21023529G007C000020

# 进入radio 2射频视图。

[AC2-wlan-ap-testap] radio 2

# 将在AC上配置clear类型的服务模板1与射频2进行关联。

[AC2-wlan-ap-testap-radio-2] service-template 1

# 使能AP的radio 2。

[AC2-wlan-ap-testap-radio-2] radio enable

[AC2-wlan-ap-testap-radio-2] return

3.4.3  Switch的配置

# 全局使能IPv6功能。

<Switch> system-view

[Switch] ipv6

# 使能DHCPv6服务器功能。

[Switch] ipv6 dhcp server enable

# 创建VLAN 100和VLAN 200,其中VLAN 100用于转发AC和AP间LWAPP隧道内的流量,VLAN 200为无线客户端接入的VLAN。

[Switch] vlan 100

[Switch-vlan100] quit

[Switch] vlan 200

[Switch-vlan200] quit

# 配置Switch与AC 1相连的GigabitEthernet1/0/1接口属性Trunk,当前Trunk口的PVID为100,允许VLAN 100和VLAN 200通过。

[Switch] interface gigabitethernet 1/0/1

[Switch-GigabitEthernet1/0/1] port link-type trunk

[Switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/1] port trunk pvid vlan 100

[Switch-GigabitEthernet1/0/1] quit

# 配置Switch与AC 2相连的GigabitEthernet1/0/2接口属性Trunk,PVID为100,允许VLAN 100和VLAN 200通过。

[Switch] interface gigabitethernet 1/0/2

[Switch-GigabitEthernet1/0/2] port link-type trunk

[Switch-GigabitEthernet1/0/2] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/2] port trunk pvid vlan 100

[Switch-GigabitEthernet1/0/2] quit

# 配置Switch与AP相连的GigabitEthernet1/0/4接口属性为Access,并允许VLAN 100通过,并使能PoE功能。

[Switch] interface gigabitethernet 1/0/4

[Switch-GigabitEthernet1/0/4] port link-type access

[Switch-GigabitEthernet1/0/4] port access vlan 100

[Switch-GigabitEthernet1/0/4] poe enable

[Switch-GigabitEthernet1/0/4] quit

# 配置VLAN 100接口的IPv6地址。

[Switch] interface vlan-interface 100

[Switch-Vlan-interface100] ipv6 address 3001::3/96

[Switch-Vlan-interface100] quit

# 配置VLAN 200接口的IPv6地址。

[Switch] interface vlan-interface 200

[Switch-Vlan-interface200] ipv6 address 3002::3/96

[Switch-Vlan-interface200] quit

# 配置DHCPv6地址池1,用于为AP分配IPv6地址。

[Switch] ipv6 dhcp pool 1

[Switch-dhcp6-pool-1] network 3001::/96

[Switch-dhcp6-pool-1] quit

[Switch] ipv6 dhcp server forbidden-address 3001::1 3001::2

# 配置在VLAN 100接口下引用地址池1。

[Switch] interface vlan-interface 100

[Switch-Vlan-interface100] ipv6 dhcp server apply pool 1

# 取消VLAN 100接口对RA消息发布的抑制。配置被管理地址的配置标志位为1,即主机通过DHCPv6服务器获取IPv6地址。配置其他信息配置标志位为1,即主机通过DHCPv6服务器获取除IPv6地址以外的其他信息。

[Switch-Vlan-interface100] ipv6 nd autoconfig managed-address-flag

[Switch-Vlan-interface100] ipv6 nd autoconfig other-flag

[Switch-Vlan-interface100] undo ipv6 nd ra halt

[Switch-Vlan-interface100] quit

# 配置DHCPv6地址池2,用于为Client分配IPv6地址。

[Switch] ipv6 dhcp pool 2

[Switch-dhcp6-pool-2] network 3002::/96

[Switch-dhcp6-pool-2] quit

[Switch] ipv6 dhcp server forbidden-address 3002::1 3002::2

# 配置在VLAN 200接口下引用地址池2。

[Switch] interface Vlan-interface 200

[Switch-Vlan-interface200] ipv6 dhcp server apply pool 2

# 取消VLAN 200接口下对RA消息发布的抑制。配置被管理地址的配置标志位为1,即主机通过DHCPv6服务器获取IPv6地址。配置其他信息配置标志位为1,即主机通过DHCPv6服务器获取除IPv6地址以外的其他信息。

[Switch-Vlan-interface200] ipv6 nd autoconfig managed-address-flag

[Switch-Vlan-interface200] ipv6 nd autoconfig other-flag

[Switch-Vlan-interface200] undo ipv6 nd ra halt

[Switch-Vlan-interface200] quit

3.5  验证配置

(1)     当MAC地址为3829-5a40-9589的Client通过SSID为service的无线服务上线时,在AC 1上通过display wlan ap all命令可以查看AP和Client的信息。

<AC1> display wlan ap all

 Total Number of APs configured           : 1                                  

 Total Number of configured APs connected : 1                                  

 Total Number of auto APs connected       : 0                                  

 Total Number of APs connected            : 1                                  

 Maximum AP capacity                      : 64                                 

 Remaining AP capacity                    : 63                                 

                                  AP Profiles                                  

 State : I = Idle,   J = Join, JA = JoinAck,   IL = ImageLoad                  

         C = Config, R = Run,  KU = KeyUpdate, KC = KeyCfm                     

         M = Master, B = Backup

--------------------------------------------------------------------------------

 AP Name                          State Model              Serial-ID

--------------------------------------------------------------------------------

 testap                           R/M   WA2620E-AGN       21023529G007C000020

-------------------------------------------------------------------------------

<AC1> display wlan client

 Total Number of Clients           : 1                                         

                               Client Information                              

 SSID: service                                                                 

--------------------------------------------------------------------------------

MAC Address    User Name            APID/RID IP Address      IPv6 Address   VLAN

--------------------------------------------------------------------------------

3829-5a40-9589 -NA-                 1   /2   0.0.0.0         -NA-           200

--------------------------------------------------------------------------------

(2)     此时在AC 2上通过display wlan ap all命令查看到AP和Client的信息,可以看见AP和Client信息已经备份到AC 2。

<AC2> display wlan ap all

 Total Number of APs configured           : 1                                  

 Total Number of configured APs connected : 1                                  

 Total Number of auto APs connected       : 0                                  

 Total Number of APs connected            : 1                                  

 Maximum AP capacity                      : 64                                 

 Remaining AP capacity                    : 63                                 

                                  AP Profiles                                  

 State : I = Idle,   J = Join, JA = JoinAck,   IL = ImageLoad                  

         C = Config, R = Run,  KU = KeyUpdate, KC = KeyCfm                     

         M = Master, B = Backup

--------------------------------------------------------------------------------

 AP Name                          State Model              Serial-ID

--------------------------------------------------------------------------------

 testap                           R/B   WA2620E-AGN       21023529G007C000020

-------------------------------------------------------------------------------

 

<AC2> display wlan client

 Total Number of Clients           : 1                                         

                               Client Information                              

 SSID: service                                                                 

--------------------------------------------------------------------------------

MAC Address    User Name            APID/RID IP Address      IPv6 Address   VLAN

--------------------------------------------------------------------------------

3829-5a40-9589 -NA-                 1   /2   0.0.0.0         -NA-           200

--------------------------------------------------------------------------------

3.6  配置文件

·     AC 1:

#                                                                               

 ipv6                                                                          

#                                                                              

 wlan backup-ac ipv6 3001::2                                                   

#                                                                              

 wlan backup-client enable                                                     

#                                                                               

vlan 1                                                                         

#                                                                              

vlan 100                                                                        

#                                                                              

vlan 200                                                                       

#                                                                               

wlan service-template 1 clear                                                  

 ssid service                                                                  

 bind WLAN-ESS 1                                                               

 service-template enable                                                       

#                                                                              

interface Vlan-interface100                                                    

 undo ipv6 nd ra halt                                                          

 ipv6 address 3001::1/96                                                       

 ipv6 address FE80::1 link-local                                               

 vrrp ipv6 vrid 1 virtual-ip FE80::10 link-local                               

 vrrp ipv6 vrid 1 virtual-ip 3001::100                                         

 vrrp ipv6 vrid 1 priority 110                                                 

 vrrp ipv6 vrid 1 preempt-mode timer delay 6                                   

#                                                                              

interface Vlan-interface200                                                    

 ipv6 address 3002::1/96                                                        

#                                                                              

interface GigabitEthernet1/0/1                                                 

 port link-type trunk                                                           

 port trunk permit vlan 1 100 200                                              

#                                                                              

interface WLAN-ESS1                                                             

 port link-type hybrid                                                         

 port hybrid vlan 1 200 untagged                                               

 port hybrid pvid vlan 200                                                      

 mac-vlan enable                                                               

#                                                                              

wlan ap testap model WA2620E-AGN id 1                                             

 serial-id 21023529G007C000020                                                

 radio 1                                                                       

  radio enable                                                                 

 radio 2                                                                       

  service-template 1                                                           

  radio enable                                                                 

#                                                                               

wlan mobility-group 1                                                          

 mobility-tunnel iactp6                                                        

 member ipv6 3001::2                                                           

 source ipv6 3001::1                                                           

 mobility-group enable                                                         

#                                                                               

·     AC 2:

#                                                                              

 ipv6                                                                          

#                                                                               

 wlan backup-ac ipv6 3001::1                                                   

#                                                                              

 wlan backup-client enable                                                      

#                                                                              

vlan 1                                                                         

#                                                                               

vlan 100                                                                       

#                                                                              

vlan 200                                                                        

#                                                                              

wlan service-template 1 clear                                                  

 ssid service                                                                   

 bind WLAN-ESS 1                                                               

 service-template enable                                                       

#                                                                              

interface Vlan-interface100                                                    

 undo ipv6 nd ra halt                                                          

 ipv6 address 3001::2/96                                                       

 ipv6 address FE80::2 link-local                                               

 vrrp ipv6 vrid 1 virtual-ip FE80::10 link-local                               

 vrrp ipv6 vrid 1 virtual-ip 3001::100                                         

 vrrp ipv6 vrid 1 preempt-mode timer delay 6                                   

#                                                                              

interface Vlan-interface200                                                    

 ipv6 address 3002::2/96                                                        

#                                                                              

interface GigabitEthernet1/0/1                                                 

 port link-type trunk                                                           

 port trunk permit vlan 1 100 200                                              

#                                                                              

interface WLAN-ESS1                                                             

 port link-type hybrid                                                         

 port hybrid vlan 1 200 untagged                                               

 port hybrid pvid vlan 200                                                      

 mac-vlan enable                                                               

#                                                                              

wlan ap testap model WA2620E-AGN id 1                                              

 serial-id 21023529G007C000020                                                

 radio 1                                                                       

  radio enable                                                                 

 radio 2                                                                       

  service-template 1                                                           

  radio enable                                                                 

#                                                                               

wlan mobility-group 1                                                          

 mobility-tunnel iactp6                                                        

 member ipv6 3001::1                                                           

 source ipv6 3001::2                                                           

 mobility-group enable                                                         

#                                                                               

·     Switch:

#                                                                              

 ipv6                                                                          

#                                                                               

 ipv6 dhcp server enable                                                       

#                                                                              

 ipv6 dhcp server forbidden-address 3001::1 3001::2                            

 ipv6 dhcp server forbidden-address 3002::1 3002::2                            

#                                                                              

vlan 1                                                                          

#                                                                              

vlan 100                                                                       

#                                                                               

vlan 200                                                                       

#                                                                              

ipv6 dhcp pool 1                                                               

 network 3001::/96                                                             

#                                                                              

ipv6 dhcp pool 2                                                               

 network 3002::/96                                                              

#                                                                              

interface Vlan-interface100                                                    

 ipv6 dhcp select server                                                        

 ipv6 dhcp server apply pool 1                                                 

 ipv6 address 3001::3/96                                                       

 ipv6 nd autoconfig managed-address-flag                                       

 ipv6 nd autoconfig other-flag                                                 

 undo ipv6 nd ra halt                                                          

#                                                                               

interface Vlan-interface200                                                    

 ipv6 dhcp select server                                                       

 ipv6 dhcp server apply pool 2                                                 

 ipv6 address 3002::3/96                                                       

 ipv6 nd autoconfig managed-address-flag                                       

 ipv6 nd autoconfig other-flag                                                  

 undo ipv6 nd ra halt                                                          

#                                                                              

interface GigabitEthernet1/0/1                                                  

 port link-type trunk                                                          

 port trunk permit vlan 1 100 200                                              

#                                                                               

interface GigabitEthernet1/0/2                                                 

 port link-type trunk                                                          

 port trunk permit vlan 1 100 200                                               

#                                                                              

interface GigabitEthernet1/0/4                                                 

 port access vlan 100                                                          

 poe enable                                                                    

#                                                                              

return

4  相关资料

·     《H3C无线控制器产品 配置指导》中的“WLAN配置指导”。

·     《H3C无线控制器产品 命令参考》中的“WLAN命令参考”。

·     《H3C无线控制器产品 配置指导》中的“可靠性配置指导”。

·     《H3C无线控制器产品 命令参考》中的“可靠性命令参考”。

 

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们