双机热备下的IPv6本地Portal认证典型配置举例(V5)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

资料版本：6W114-20210416

 

目  录

1 简介

2 配置前提

3 配置举例

3.1 组网需求

3.2 配置思路

3.3 配置注意事项

3.4 配置步骤

3.4.1 AC 1的配置

3.4.2 AC 2的配置

3.4.3 Switch 1的配置

3.4.4 Switch 2的配置

3.4.5 RADIUS Server的配置

3.5 验证配置

3.6 配置文件

4 相关资料

 

1  简介

本文介绍了双机热备下的本地Portal认证典型配置举例。

2  配置前提

本文档不严格与具体软、硬件版本对应，如果使用过程中与产品实际情况有差异，请参考相关产品手册，或以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置，为了保证配置效果，请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解WLAN无线接入、Portal认证、双AC备份等特性。

3  配置举例

3.1  组网需求

如图1所示，为了提高无线用户接入的可靠性，要求在AC 1和AC 2之间实现双机热备功能，并且对Portal用户的数据进行备份。具体需求如下：

·     AC1和AC2通过VLAN 10传输双机热备报文。

·     AC 1正常工作的情况下，Client通过AC 1进行Portal认证接入到外网。AC 1发生故障的情况下，Client通过AC 2接入到外网，保证业务流量切换不被中断。

·     采用RADIUS服务器作为认证/计费服务器，采用AC作为本地Portal服务器。

·     当Portal用户异常下线时，为了防止AC误认为异常下线用户仍在线，可以通过用户闲置切断功能来实现。

图1 双机热备下的本地Portal认证组网图

 

3.2  配置思路

·     为了避免两台AC和上下行设备产生环路，并在主备切换时，尽快完成收敛，需要在AC 1和AC 2上使能MSTP功能，并设置AC 1为根桥。

·     当发生主备切换时，为了保证AC的上下行不丢包，需要分别在AC 1和AC 2的上下行接口上配置VRRP备份组。

·     为了使AC 1成为VRRP备份组的Master AC，需要在VRRP备份组中为AC 1配置较高的优先级。

3.3  配置注意事项

·     确保AC与RADIUS服务器的路由可达。

·     AC 1与AC 2上，涉及RADIUS、Domain、Portal、WLAN等的相关配置要保持一致。

·     配置AP的序列号时请确保该序列号与AP唯一对应，AP的序列号可以通过AP设备背面的标签获取。

3.4  配置步骤

3.4.1  AC 1的配置

(1)     配置AC 1的接口

# 全局使能IPv6功能。

<AC1> system-view

[AC1] ipv6

# 创建VLAN 10作为双机热备的VLAN。

[AC1] vlan 10

[AC1-vlan10] quit

# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IPv4和IPv6地址。AP将通过该VLAN与AC建立LWAPP隧道。

[AC1] vlan 100

[AC1-vlan100] quit

[AC1] interface vlan-interface 100

[AC1-Vlan-interface100] ip address 192.168.1.1 24

[AC1-Vlan-interface100] ipv6 address 3001::1 96

[AC1-Vlan-interface100] quit

# 创建VLAN 200作为WLAN-ESS接口的缺省VLAN。

[AC1] vlan 200

[AC1-vlan200] quit

# 创建VLAN 300作为Client接入的业务VLAN，并为该接口配置IPv4和IPv6地址。

[AC1] vlan 300

[AC1-vlan300] quit

[AC1] interface vlan-interface 300

[AC1-Vlan-interface300] ip address 192.168.3.1 24

[AC1-Vlan-interface300] ipv6 address fe80::1 link-local

[AC1-Vlan-interface300] ipv6 address 3003::1 96

[AC1-Vlan-interface300] quit

# 创建VLAN 1作为与RADIUS server通信的VLAN，并为该接口配置IPv4和IPv6地址。

[AC1] vlan 1

[AC1-vlan1] quit

[AC1] interface vlan-interface 1

[AC1-Vlan-interface1] ip address 192.168.100.147 24

[AC1-Vlan-interface1] ipv6 address fe80::2 link-local

[AC1-Vlan-interface1] ipv6 address 2003::1 64

[AC1-Vlan-interface1] quit

# 配置AC 1与AC 2相连的GigabitEthernet1/0/2接口的链路类型为Access，当前Access口允许VLAN 10通过。

[AC1] interface gigabitethernet 1/0/2

[AC1-GigabitEthernet1/0/2] port link-type access

[AC1-GigabitEthernet1/0/2] port access vlan 10

[AC1-GigabitEthernet1/0/2] quit

# 配置AC1的下行链路GigabitEthernet1/0/3接口的链路类型为Trunk，当前Trunk口的PVID为100，并允许VLAN 100和VLAN 300的报文通过。

[AC1] interface gigabitethernet 1/0/3

[AC1-GigabitEthernet1/0/3] port link-type trunk

[AC1-GigabitEthernet1/0/3] port trunk permit vlan 100 300

[AC1-GigabitEthernet1/0/3] port trunk pvid vlan 100

[AC1-GigabitEthernet1/0/3] quit

(2)     配置MSTP

# 配置生成树的工作模式为MSTP。

[AC1] stp mode mstp

# 激活MST域。

[AC1] stp region-configuration

[AC1-mst-region] active region-configuration

[AC1-mst-region] quit

# 配置AC 1为根桥。

[AC1] stp root primary

# 使能STP功能。

[AC1] stp enable

(3)     配置VRRP

# 创建VRRP备份组1，并配置VRRP备份组1的虚拟IPv4地址为192.168.3.100，虚拟IPv6地址为FE80::30和3003::100。

[AC1] interface vlan-interface 300

[AC1-Vlan-interface300] vrrp vrid 1 virtual-ip 192.168.3.100

[AC1-Vlan-interface300] vrrp ipv6 vrid 1 virtual-ip fe80::30 link-local

[AC1-Vlan-interface300] vrrp ipv6 vrid 1 virtual-ip 3003::100

# 配置VLAN接口300在VRRP备份组1中的优先级为254。

[AC1-Vlan-interface300] vrrp vrid 1 priority 254

[AC1-Vlan-interface300] vrrp ipv6 vrid 1 priority 254

[AC1-Vlan-interface300] quit

# 创建VRRP备份组2，并配置VRRP备份组2的虚拟IPv4地址为192.168.100.245，虚拟IPv6地址为FE80::40和2003::100。

[AC1] interface vlan-interface 1

[AC1-Vlan-interface1] vrrp vrid 2 virtual-ip 192.168.100.245

[AC1-Vlan-interface1] vrrp ipv6 vrid 2 virtual-ip fe80::40 link-local

[AC1-Vlan-interface1] vrrp ipv6 vrid 2 virtual-ip 2003::100

# 配置VLAN接口1在VRRP备份组2中的优先级为254。

[AC1-Vlan-interface1] vrrp vrid 2 priority 254

[AC1-Vlan-interface1] vrrp ipv6 vrid 2 priority 254

[AC1-Vlan-interface400] quit

(4)     配置Portal认证

# 配置IPv4 Portal服务器：名称为officev4，IPv4地址为192.168.3.100（VRRP备份组1的虚拟IPv4地址），URL为http://192.168.3.100/portal/logon.htm。

[AC1] portal server officev4 ip 192.168.3.100 url http://192.168.3.100/portal/logon.htm

# 配置IPv6 Portal服务器：名称为officev6，IPv6地址为3003::100（VRRP备份组1的虚拟IPv6地址），URL为http://[3003::100]/portal/logon.htm。

[AC1] portal server officev6 ipv6 3003::100 url http://[3003::100]/portal/logon.htm

# 配置本地Portal服务器支持HTTP协议。

[AC1] portal local-server http

# 在VLAN接口300上配置Portal用户报文的控制模式为MAC，IPv4或者IPv6用户通过Portal认证上线后，同时允许该用户的IPv4和IPv6报文通过认证接口。

[AC1] interface vlan-interface 300

[AC1-Vlan-interface300] portal control-mode mac

# 在VLAN接口300上使能Portal认证，并配置为直接认证方式。

[AC1-Vlan-interface300] portal server officev4 method direct

[AC1-Vlan-interface300] portal server officev6 method direct

[AC1-Vlan-interface300] quit

(5)     配置IPv4 RADIUS方案

# 创建名为rs4的RADIUS方案并进入其视图。

[AC1] radius scheme rs4

# 配置RADIUS方案的主认证服务器的IPv4地址为192.168.100.240，认证报文的共享密钥设置为明文123456。

[AC1-radius-rs4] primary authentication 192.168.100.240

[AC1-radius-rs4] key authentication 123456

# 配置发送给RADIUS服务器的用户名不携带ISP域名。

[AC1-radius-rs4] user-name-format without-domain

[AC1-radius-rs4] quit

(6)     配置IPv6 RADIUS方案

# 创建名为rs6的RADIUS方案并进入其视图。

[AC1] radius scheme rs6

# 配置RADIUS方案的主认证服务器的IPv6地址为2003::2，认证报文的共享密钥设置为明文123456。

[AC1-radius-rs6] primary authentication ipv6 2003::2

[AC1-radius-rs6] key authentication 123456

# 配置发送给RADIUS服务器的用户名不携带ISP域名。

[AC1-radius-rs6] user-name-format without-domain

[AC1-radius-rs6] quit

(7)     配置IPv4认证域

# 创建名为dm4的ISP域，并进入其视图。

[AC1] domain dm4

# 配置Portal用户使用RADIUS方案rs4进行认证，不对用户使用的网络服务进行授权和计费。

[AC1-isp-dm4] authentication portal radius-scheme rs4

[AC1-isp-dm4] authorization portal none

[AC1-isp-dm4] accounting portal none

# 允许ISP域office中的用户启用闲置切断功能，闲置检测时间为50分钟，允许用户闲置时的最小数据流量为1024个字节。

[AC1-isp-dm4] idle-cut enable 50 1024

[AC1-isp-dm4] quit

(8)     配置IPv6认证域

# 创建名为dm6的ISP域，并进入其视图。

[AC1] domain dm6

# 配置Portal用户使用RADIUS方案rs6进行认证，不对用户使用的网络服务进行授权和计费。

[AC1-isp-dm6] authentication portal radius-scheme rs6

[AC1-isp-dm6] authorization portal none

[AC1-isp-dm6] accounting portal none

# 允许ISP域office中的用户启用闲置切断功能，闲置检测时间为50分钟，允许用户闲置时的最小数据流量为1024个字节。

[AC1-isp-dm6] idle-cut enable 50 1024

[AC1-isp-dm6] quit

(9)     配置Portal支持双机热备

# 配置VLAN接口300属于Portal备份组1。

[AC1] interface vlan-interface 300

[AC1-Vlan-interface300] portal backup-group 1

[AC1-Vlan-interface300] quit

# 配置双机热备模式下的设备ID为1，输入“Y”确认。

[AC1] nas device-id 1

Warning: This command will cut all user connections on this device. Continue? [Y/N]Y

# 配置发送RADIUS报文使用的源IPv4地址为VRRP备份组2的虚拟IPv4地址。

[AC1] radius nas-ip 192.168.100.245

# 配置发送RADIUS报文使用的源IPv6地址为VRRP备份组2的虚拟IPv6地址。

[AC1] radius nas-ip ipv6 2003::100

# 指定IPv4 Portal用户的认证域为dm4。

[AC1] interface vlan-interface 300

[AC1-Vlan-interface300] portal domain dm4

# 指定IPv6 Portal用户的认证域为dm6。

[AC1-Vlan-interface300] portal domain ipv6 dm6

[AC1-Vlan-interface300] quit

(10)     配置WLAN服务

# 配置全局备份AC的IPv4地址为192.168.1.2。

[AC1] wlan backup-ac ip 192.168.1.2

# 配置全局备份AC的IPv6地址为3001::2。

[AC1] wlan backup-ac ipv6 3001::2

# 使能AC间热备份功能。

[AC1] hot-backup enable

# 配置AC间用于热备份的VLAN为VLAN 10。

[AC1] hot-backup vlan 10

# 创建接口WLAN-ESS 1，并设置端口的链路类型为Hybrid。

[AC1] interface wlan-ess 1

[AC1-WLAN-ESS1] port link-type hybrid

# 配置当前Hybrid端口的PVID为VLAN 200，禁止VLAN 1通过并允许VLAN 200和VLAN 300不带Tag通过。

[AC1-WLAN-ESS1] undo port hybrid vlan 1

[AC1-WLAN-ESS1] port hybrid vlan 200 300 untagged

[AC1-WLAN-ESS1] port hybrid pvid vlan 200

# 使能MAC VLAN功能。

[AC1-WLAN-ESS1] mac-vlan enable

[AC1-WLAN-ESS1] quit

# 配置WLAN服务模板，SSID为service，将接口WLAN-ESS 1与该服务模板绑定，并开启WLAN服务。

[AC1] wlan service-template 1 clear

[AC1-wlan-st-1] ssid service

[AC1-wlan-st-1] bind wlan-ess 1

[AC1-wlan-st-1] service-template enable

[AC1-wlan-st-1] quit

# 在AC 1的AP视图下配置AP名称为officeap，型号名称选择WA2620E-AGN。

[AC1] wlan ap officeap model WA2620E-AGN

# 设置AP的序列号为21023529G007C000020。

[AC1-wlan-ap-officeap] serial-id 21023529G007C000020

# 配置AP的接入优先级设置为7，该值越大优先级越高，缺省为4。

[AC1-wlan-ap-officeap] priority level 7

# 进入radio 2射频视图。

[AC1-wlan-ap-officeap] radio 2

# 将在AC上配置的clear类型的服务模板1与射频2进行关联，同时设置绑定到该射频的VLAN为VLAN 300。

[AC1-wlan-ap-officeap-radio-2] service-template 1 vlan-id 300

# 使能AP的radio 2。

[AC1-wlan-ap-officeap-radio-2] radio enable

[AC1-wlan-ap-officeap-radio-2] quit

[AC1-wlan-ap-officeap] quit

(11)     配置双机热备

# 配置备份VLAN为VLAN 10。

[AC1] dhbk vlan 10

# 使能双机热备功能，且支持对称路径。

[AC1] dhbk enable backup-type symmetric-path

3.4.2  AC 2的配置

(1)     配置AC 2的接口

# 全局使能IPv6功能。

<AC2> system-view

[AC2] ipv6

# 创建VLAN 10作为双机热备的VLAN。

[AC2] vlan 10

[AC2-vlan10] quit

# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IPv4和IPv6地址。AP将通过该VLAN与AC建立LWAPP隧道。

[AC2] vlan 100

[AC2-vlan100] quit

[AC2] interface vlan-interface 100

[AC2-Vlan-interface100] ip address 192.168.1.2 24

[AC2-Vlan-interface100] ipv6 address 3001::2 96

[AC2-Vlan-interface100] quit

# 创建VLAN 200作为WLAN-ESS接口的缺省VLAN。

[AC2] vlan 200

[AC2-vlan200] quit

# 创建VLAN 300作为Client接入的业务VLAN，并为该接口配置IPv4和IPv6地址。

[AC2] vlan 300

[AC2-vlan300] quit

[AC2] interface vlan-interface 300

[AC2-Vlan-interface300] ip address 192.168.3.2 24

[AC2-Vlan-interface300] ipv6 address fe80::3 link-local

[AC2-Vlan-interface300] ipv6 address 3003::2 96

[AC2-Vlan-interface300] quit

# 创建VLAN 1作为与RADIUS server通信的VLAN，并为该接口配置IPv4和IPv6地址。

[AC2] vlan 1

[AC2-vlan1] quit

[AC2] interface vlan-interface 1

[AC2-Vlan-interface1] ip address 192.168.100.163 24

[AC2-Vlan-interface1] ipv6 address fe80::4 link-local

[AC2-Vlan-interface1] ipv6 address 2003::3 64

[AC2-Vlan-interface1] quit

# 配置AC 1与AC 2相连的GigabitEthernet1/0/2接口的链路类型为Access，当前Access口允许VLAN 10通过。

[AC2] interface gigabitethernet 1/0/2

[AC2-GigabitEthernet1/0/2] port link-type access

[AC2-GigabitEthernet1/0/2] port access vlan 10

[AC2-GigabitEthernet1/0/2] quit

# 配置AC 2下行链路的GigabitEthernet1/0/3接口的链路类型为Trunk，当前Trunk口的PVID为100，并允许VLAN 100和VLAN 300的报文通过。

[AC2] interface gigabitethernet 1/0/3

[AC2-GigabitEthernet1/0/3] port link-type trunk

[AC2-GigabitEthernet1/0/3] port trunk permit vlan 100 300

[AC2-GigabitEthernet1/0/3] port trunk pvid vlan 100

[AC2-GigabitEthernet1/0/3] quit

(2)     配置MSTP

# 配置生成树的工作模式为MSTP。

[AC2] stp mode mstp

# 激活MST域。

[AC2] stp region-configuration

[AC2-mst-region] active region-configuration

[AC2-mst-region] quit

# 使能STP功能。

[AC2] stp enable

(3)     配置VRRP

# 创建VRRP备份组1，并配置VRRP备份组1的虚拟IPv4地址为192.168.3.100，虚拟IPv6地址为FE80::30和3003::100。

[AC2] interface vlan-interface 300

[AC2-Vlan-interface300] vrrp vrid 1 virtual-ip 192.168.3.100

[AC2-Vlan-interface300] vrrp ipv6 vrid 1 virtual-ip fe80::30 link-local

[AC2-Vlan-interface300] vrrp ipv6 vrid 1 virtual-ip 3003::100

[AC2-Vlan-interface300] quit

# 创建VRRP备份组2，并配置VRRP备份组2的虚拟IPv4地址为192.168.100.245，虚拟IPv6地址为FE80::40和2003::100。

[AC2] interface vlan-interface 1

[AC2-Vlan-interface1] vrrp vrid 2 virtual-ip 192.168.100.245

[AC2-Vlan-interface1] vrrp ipv6 vrid 2 virtual-ip fe80::40 link-local

[AC2-Vlan-interface1] vrrp ipv6 vrid 2 virtual-ip 2003::100

[AC2-Vlan-interface1] quit

(4)     配置Portal认证

# 配置IPv4 Portal服务器：名称为officev4，IPv4地址为192.168.3.100（VRRP备份组1的虚拟IPv4地址），URL为http://192.168.3.100/portal/logon.htm。

[AC2] portal server officev4 ip 192.168.3.100 url http://192.168.3.100/portal/logon.htm

# 配置IPv6 Portal服务器：名称为officev6，IPv6地址为3003::100（VRRP备份组1的虚拟IPv6地址），URL为http://[3003::100]/portal/logon.htm。

[AC1] portal server officev6 ipv6 3003::100 url http://[3003::100]/portal/logon.htm

# 配置本地Portal服务器支持HTTP协议。

[AC2] portal local-server http

# 在VLAN接口300上配置Portal用户报文的控制模式为MAC，IPv4或者IPv6用户通过Portal认证上线后，同时允许该用户的IPv4和IPv6报文通过认证接口。

[AC2] interface vlan-interface 300

[AC2-Vlan-interface300] portal control-mode mac

# 在VLAN接口300上使能Portal认证，并配置为直接认证方式。

[AC2-Vlan-interface300] portal server officev4 method direct

[AC2-Vlan-interface300] portal server officev6 method direct

[AC2-Vlan-interface300] quit

(5)     配置IPv4 RADIUS方案

# 创建名为rs4的RADIUS方案并进入其视图。

[AC2] radius scheme rs4

# 配置RADIUS方案的主认证服务器的IPv4地址为192.168.100.240，认证报文的共享密钥设置为明文123456。

[AC2-radius-rs4] primary authentication 192.168.100.240

[AC2-radius-rs4] key authentication 123456

# 配置发送给RADIUS服务器的用户名不携带ISP域名。

[AC2-radius-rs4] user-name-format without-domain

[AC2-radius-rs4] quit

(6)     配置IPv6 RADIUS方案

# 创建名为rs6的RADIUS方案并进入其视图。

[AC2] radius scheme rs6

# 配置RADIUS方案的主认证服务器的IPv6地址为2003::2，认证报文的共享密钥设置为明文123456。

[AC2-radius-rs6] primary authentication ipv6 2003::2

[AC2-radius-rs6] key authentication 123456

# 配置发送给RADIUS服务器的用户名不携带ISP域名。

[AC2-radius-rs6] user-name-format without-domain

[AC2-radius-rs6] quit

(7)     配置IPv4认证域

# 创建名为dm4的ISP域，并进入其视图。

[AC2] domain dm4

# 配置Portal用户使用RADIUS方案rs4进行认证，不对用户使用的网络服务进行授权和计费。

[AC2-isp-dm4] authentication portal radius-scheme rs4

[AC2-isp-dm4] authorization portal none

[AC2-isp-dm4] accounting portal none

# 允许ISP域office中的用户启用闲置切断功能，闲置检测时间为50分钟，允许用户闲置时的最小数据流量为1024个字节。

[AC2-isp-dm4] idle-cut enable 50 1024

[AC2-isp-dm4] quit

(8)     配置IPv6认证域

# 创建名为dm6的ISP域，并进入其视图。

[AC2] domain dm6

# 配置Portal用户使用RADIUS方案rs6进行认证，不对用户使用的网络服务进行授权和计费。

[AC2-isp-dm6] authentication portal radius-scheme rs6

[AC2-isp-dm6] authorization portal none

[AC2-isp-dm6] accounting portal none

# 允许ISP域office中的用户启用闲置切断功能，闲置检测时间为50分钟，允许用户闲置时的最小数据流量为1024个字节。

[AC2-isp-dm6] idle-cut enable 50 1024

[AC2-isp-dm6] quit

(9)     配置Portal支持双机热备

# 配置VLAN接口300属于Portal备份组1。

[AC2] interface vlan-interface 300

[AC2-Vlan-interface300] portal backup-group 1

[AC2-Vlan-interface300] quit

# 配置双机热备模式下的设备ID为2，输入“Y”确认。

[AC2] nas device-id 2

Warning: This command will cut all user connections on this device. Continue? [Y/N]Y

# 配置发送RADIUS报文使用的源IPv4地址为VRRP备份组2的虚拟IPv4地址。

[AC2] radius nas-ip 192.168.100.245

# 配置发送RADIUS报文使用的源IPv6地址为VRRP备份组2的虚拟IPv6地址。

[AC1] radius nas-ip ipv6 2003::100

# 指定IPv4 portal用户的认证域为dm4。

[AC2] interface vlan-interface 300

[AC2-Vlan-interface300] portal domain dm4

# 指定IPv6 Portal用户的认证域为dm6。

[AC2-Vlan-interface300] portal domain ipv6 dm6

[AC2-Vlan-interface300] quit

(10)     配置WLAN服务

# 配置全局备份AC的IPv4地址为192.168.1.1。

[AC2] wlan backup-ac ip 192.168.1.1

# 配置全局备份AC的IPv6地址为3001::1。

[AC1] wlan backup-ac ipv6 3001::1

# 使能AC间热备份功能。

[AC2] hot-backup enable

# 配置AC间用于热备份的VLAN为VLAN 10。

[AC2] hot-backup vlan 10

# 创建接口WLAN-ESS 1，并设置端口的链路类型为Hybrid。

[AC2] interface wlan-ess 1

[AC2-WLAN-ESS1] port link-type hybrid

# 配置当前Hybrid端口的PVID为VLAN 200，禁止VLAN 1通过并允许VLAN 200不带Tag通过。

[AC2-WLAN-ESS1] undo port hybrid vlan 1

[AC2-WLAN-ESS1] port hybrid vlan 200 300 untagged

[AC2-WLAN-ESS1] port hybrid pvid vlan 200

[AC2-WLAN-ESS1] mac-vlan enable

[AC2-WLAN-ESS1] quit

# 配置WLAN服务模板，SSID为service，将接口WLAN-ESS 1与该服务模板绑定，并开启WLAN服务。

[AC2] wlan service-template 1 clear

[AC2-wlan-st-1] ssid service

[AC2-wlan-st-1] bind wlan-ess 1

[AC2-wlan-st-1] service-template enable

[AC2-wlan-st-1] quit

# 在AC 2的AP视图下配置AP名称为officeap，型号名称选择WA2620E-AGN。

[AC2] wlan ap officeap model WA2620E-AGN

# 设置AP的序列号为21023529G007C000020。

[AC2-wlan-ap-officeap] serial-id 21023529G007C000020

# 进入radio 2射频视图。

[AC2-wlan-ap-officeap] radio 2

# 将在AC上配置的clear类型的服务模板1与射频2进行关联，同时设置绑定到该射频的VLAN为VLAN 300。

[AC2-wlan-ap-officeap-radio-2] service-template 1 vlan-id 300

# 使能AP的radio 2。

[AC2-wlan-ap-officeap-radio-2] radio enable

[AC2-wlan-ap-officeap-radio-2] quit

[AC2-wlan-ap-officeap] quit

(11)     配置双机热备

# 配置备份VLAN为VLAN 10。

[AC2] dhbk vlan 10

# 使能双机热备功能，且支持对称路径。

[AC2] dhbk enable backup-type symmetric-path

3.4.3  Switch 1的配置

# 全局使能IPv6功能。

<Switch1> system-view

[Switch1] ipv6

# 配置生成树的工作模式为MSTP。

[Switch1] stp mode mstp

# 激活MST域。

[Switch1] stp region-configuration

[Switch1-mst-region] active region-configuration

[Switch1-mst-region] quit

# 使能STP功能。

[Switch1] stp enable

3.4.4  Switch 2的配置

(1)     配置Switch2的接口

# 全局使能IPv6功能。

<Switch2> system-view

[Switch2] ipv6

# 创建VLAN 100和VLAN 300，其中VLAN 100用于转发AC和AP间LWAPP隧道内的流量，VLAN 300为无线客户端接入的VLAN。

[Switch2] vlan 100

[Switch2-vlan100] quit

[Switch2] vlan 300

[Switch2-vlan300] quit

# 配置Switch 2与AC 1相连的GigabitEthernet1/0/1接口链路类型为Trunk，当前Trunk口的PVID为100，允许VLAN 100和VLAN 300通过。

[Switch2] interface gigabitethernet 1/0/1

[Switch2-GigabitEthernet1/0/1] port link-type trunk

[Switch2-GigabitEthernet1/0/1] port trunk permit vlan 100 300

[Switch2-GigabitEthernet1/0/1] port trunk pvid vlan 100

[Switch2-GigabitEthernet1/0/1] quit

# 配置Switch 2与AC 2相连的GigabitEthernet1/0/2接口链路类型为Trunk，当前Trunk口的PVID为100，允许VLAN 100和VLAN 300通过。

[Switch2] interface gigabitethernet 1/0/2

[Switch2-GigabitEthernet1/0/2] port link-type trunk

[Switch2-GigabitEthernet1/0/2] port trunk permit vlan 100 300

[Switch2-GigabitEthernet1/0/2] port trunk pvid vlan 100

[Switch2-GigabitEthernet1/0/2] quit

# 配置Switch 2与AP相连的GigabitEthernet1/0/3接口链路类型为Access，当前Access口允许VLAN 100通过，并使能PoE功能。

[Switch2] interface gigabitethernet 1/0/3

[Switch2-GigabitEthernet1/0/3] port link-type access

[Switch2-GigabitEthernet1/0/3] port access vlan 100

[Switch2-GigabitEthernet1/0/3] poe enable

[Switch2-GigabitEthernet1/0/3] quit

# 配置生成树的工作模式为MSTP。

[Switch2] stp mode mstp

# 激活MST域。

[Switch2] stp region-configuration

[Switch2-mst-region] active region-configuration

[Switch2-mst-region] quit

# 使能STP功能。

[Switch2] stp enable

3.4.5  RADIUS Server的配置

 

# 增加接入设备

登录进入IMC管理平台，选择“用户”页签，单击导航树中的[接入策略管理/接入设备管理/接入设备配置]菜单项，进入“接入设备配置”页面，在该页面中单击<增加>按钮，进入“增加接入设备”页面。

·     设置与AC交互报文时使用的认证、计费共享密钥为“123456”；

·     设置认证及计费的端口号分别为“1812”和“1813”；

·     选择接入设备类型为“H3C(General)”；

·     在设备列表中，单击<手工增加>按钮，添加IP地址为192.168.100.245的接入设备；

·     单击<增加IPv6设备>按钮，进入“手工增加接入设备”页面，填写起始IP地址为2003::100，单击<确定>按钮完成操作；

·     其它参数采用缺省值，并单击<确定>按钮完成操作。

图2 增加IPv4接入设备

 

图3 增加IPv6接入设备

 

# 增加接入策略

选择“用户”页签，单击导航树中的[接入策略管理/接入策略管理]菜单项，进入“接入策略管理”页面，单击“增加”按钮，进入“增加接入策略”页面。

·     接入策略名为“portal”，该名称可以自行定义；

·     业务分组选择“未分组”；

·     其他配置采用缺省配置；

·     单击<确定>按钮完成操作。

图4 增加接入策略

 

# 增加接入服务

选择“用户”页签，单击导航树中的[接入策略管理/接入服务管理]菜单项，进入“接入服务管理”页面，点击<增加>按钮，进入“增加接入服务”页面。

·     输入服务名“portal auth”，该名称可以自行定义；

·     业务分组“未分组”；

·     缺省接入策略选择“portal”，即上一步配置的接入策略名；

·     其它参数采用缺省值，并单击<确定>按钮完成操作。

图5 增加接入服务

 

# 配置接入用户

选择“用户”页签，单击导航树中的[接入用户管理/接入用户]菜单项，进入“接入用户”页面，在该页面中单击<增加>按钮，进入“增加接入用户”页面。

·     在增加接入用户页面，单击<增加用户>按钮弹出增加用户窗口；

·     输入用户名“admin”；

·     输入证件号码“12345”；

·     单击<检查是否可用>按钮；

·     如用户姓名和证件号码可用，单击<确定>按钮完成操作。

图6 增加用户

 

在“增加接入用户”页面，按如下方式配置。

·     输入账号名“portal”；

·     输入密码“123456”；

·     接入服务选择“portal auth”；

·     其他配置保持默认；

·     单击<确定>按钮完成操作。

图7 增加接入用户

 

3.5  验证配置

# Client从AC 1成功上线后，在AC 1上通过命令display portal user all查看该用户的认证情况。可以看到Portal用户的工作模式为主用户，表示该用户是由AC 1上线。

[AC1] display portal user all

 Index:1

 State:ONLINE

 SubState:NONE

 ACL:NONE

 Work-mode:primary

 MAC              IP                Vlan   Interface

 ----------------------------------------------------------------------------

 0021-632f-e4d1   192.168.3.5        300    Vlan-interface300

 Total 1 user(s) matched, 1 listed.

# Client从AC 1成功上线后，在AC 2通过命令display portal user all查看该用户的认证情况。可以看到Portal用户的工作模式为备用户，表示该用户的认证信息同步到AC 2上。

[AC2] display portal user all

 Index:0

 State:ONLINE

 SubState:NONE

 ACL:NONE

 Work-mode:secondary

 MAC              IP                Vlan   Interface

 ----------------------------------------------------------------------------

 0021-632f-e4d1   192.168.3.5        300    Vlan-interface300

 Total 1 user(s) matched, 1 listed.

# 通过将AC 1下电模拟主AC宕机的情形，使得AC发生主备切换，此时，在AC 2上便可以查看到用户的状态由“secondary”转换为“stand-alone”状态，说明此时只有AC 2处于工作状态。

[AC2] display portal user all

 Index:3

 State:ONLINE

 SubState:NONE

 ACL:NONE

 Work-mode:stand-alone

 MAC              IP                Vlan   Interface

 ----------------------------------------------------------------------------

 0021-632f-e4d1   192.168.3.5        300    Vlan-interface300

 Total 1 user(s) matched, 1 listed.

3.6  配置文件

·     AC 1的配置文件：

#                                                                              

 radius nas-ip ipv6 2003::0100                                                 

 nas device-id 1                                                               

#                                                                              

 ipv6                                                                           

#                                                                              

 portal server officev6 ipv6 3003::100 url http://[3003::100]/portal/logon.htm s

erver-type imc                                                                  

 portal server officev4 ip 192.168.3.100 url http://192.168.3.100/portal/logon.h

tm server-type imc                                                             

 portal free-rule 0 source interface GigabitEthernet1/0/1 destination any      

 portal local-server http                                                      

#                                                                              

 wlan backup-ac ip 192.168.1.2                                                  

 wlan backup-ac ipv6 3001::2                                                   

#                                                                              

 hot-backup enable domain 1                                                     

 hot-backup vlan 10                                                            

#                                                                              

vlan 1                                                                         

#                                                                              

vlan 10                                                                        

#                                                                               

vlan 100                                                                       

#                                                                              

vlan 200                                                                        

#                                                                              

vlan 300                                                                       

#                                                                               

radius scheme rs6                                                              

 primary authentication ipv6 2003::0002                                        

 primary accounting ipv6 2003::0002                                             

 key authentication cipher $c$3$YvYFuVf9PIY6Jg/eYeuH7VLV0vbhAmh0gg==           

 user-name-format without-domain                                               

radius scheme rs4                                                               

 primary authentication 192.168.100.240                                        

 primary accounting 192.168.100.240                                            

 key authentication cipher $c$3$zdQLHG1FGgNpAuye0JS333lP6s0KQNvmrw==            

 key accounting cipher $c$3$OIc+iiVqnz13BQBHa/LiDTlVVIFQ0RbZJA==               

 user-name-format without-domain                                               

#                                                                              

domain dm4                                                                     

 authentication portal radius-scheme rs4                                       

 authorization portal none                                                     

 accounting portal none                                                        

 access-limit disable                                                          

 state active                                                                  

 idle-cut enable 50 1024                                                        

 self-service-url disable                                                      

domain dm6                                                                     

 authentication portal radius-scheme rs6                                       

 authorization portal none                                                     

 accounting portal none                                                        

 access-limit disable                                                          

 state active                                                                  

 idle-cut enable 50 1024                                                       

 self-service-url disable                                                       

#                                                                              

 stp instance 0 root primary                                                   

 stp enable                                                                     

#                                                                              

wlan service-template 1 clear                                                  

 ssid service                                                                   

 bind WLAN-ESS 1                                                               

 service-template enable                                                       

#                                                                               

interface Vlan-interface1                                                      

 ipv6 address 2003::1/64                                                       

 ipv6 address FE80::2 link-local                                                

 ip address 192.168.100.147 255.255.255.0                                      

 vrrp vrid 2 virtual-ip 192.168.100.245                                        

 vrrp vrid 2 priority 254                                                      

 vrrp ipv6 vrid 2 virtual-ip FE80::40 link-local                               

 vrrp ipv6 vrid 2 virtual-ip 2003::100                                         

 vrrp ipv6 vrid 2 priority 254                                                 

#                                                                               

interface Vlan-interface10                                                     

 ipv6 address 3010::1/96                                                       

 ip address 192.168.10.1 255.255.255.0                                         

#                                                                              

interface Vlan-interface100                                                    

 ipv6 address 3001::1/96                                                       

 ip address 192.168.1.1 255.255.255.0                                          

#                                                                              

interface Vlan-interface200                                                    

#                                                                              

interface Vlan-interface300                                                    

 ipv6 address 3003::1/96                                                        

 ipv6 address FE80::1 link-local                                               

 ip address 192.168.3.1 255.255.255.0                                          

 vrrp vrid 1 virtual-ip 192.168.3.100                                           

 vrrp vrid 1 priority 254                                                      

 vrrp ipv6 vrid 1 virtual-ip FE80::30 link-local                               

 vrrp ipv6 vrid 1 virtual-ip 3003::100                                          

 vrrp ipv6 vrid 1 priority 254                                                 

 portal control-mode mac

 portal server officev4 method direct                                          

 portal server officev6 method direct                                           

 portal domain dm4                                                             

 portal domain ipv6 dm6                                                        

 portal backup-group 1                                                          

#                                                                              

interface GigabitEthernet1/0/1                                                 

 port link-type trunk                                                           

 port trunk permit vlan 1 100 300                                              

#                                                                              

interface GigabitEthernet1/0/2                                                 

 port link-type trunk                                                          

 port trunk permit vlan 1 100                                                  

#                                                                              

interface GigabitEthernet1/0/3                                                 

 port access vlan 10                                                           

#                                                                              

interface WLAN-ESS1                                                             

 port link-type hybrid                                                         

 undo port hybrid vlan 1                                                       

 port hybrid vlan 200 300 untagged                                              

 port hybrid pvid vlan 200                                                     

 mac-vlan enable                                                               

#                                                                               

wlan ap ap1 model WA2620E-AGN id 1                                             

 serial-id 21023529G007C000020                                                

 radio 1                                                                        

  radio enable                                                                 

 radio 2                                                                       

  service-template 1 vlan-id 300                                                

  radio enable                                                                 

#                                                                              

 dhbk enable backup-type symmetric-path                                        

 dhbk vlan 10                                                                  

#                                                                              

return                                                                         

·     AC 2的配置文件：

#                                                                               

 radius nas-ip ipv6 2003::0100                                                 

 nas device-id 2                                                               

#                                                                              

 ipv6                                                                          

#                                                                              

 portal server officev4 ip 192.168.3.100 url http://192.168.3.100/portal/logon.h

tm server-type imc                                                             

 portal server officev6 ipv6 3003::100 url http://[3003::100]/portal/logon.htm s

erver-type imc                                                                  

 portal free-rule 0 source interface GigabitEthernet1/0/1 destination any      

 portal local-server http                                                      

#                                                                               

 wlan backup-ac ip 192.168.1.1                                                 

 wlan backup-ac ipv6 3001::1                                                   

#                                                                               

 hot-backup enable domain 1                                                    

 hot-backup vlan 10                                                            

#                                                                               

vlan 1                                                                         

#                                                                              

vlan 10                                                                         

#                                                                              

vlan 100                                                                       

#                                                                              

vlan 200                                                                        

#                                                                              

vlan 300                                                                       

#                                                                               

radius scheme rs4                                                              

 primary authentication 192.168.100.240                                        

 key authentication cipher $c$3$ezwUorHFXLxU0eaO2OyoyURVFuZwUNflAA==           

 user-name-format without-domain                                               

radius scheme rs6                                                              

 primary authentication ipv6 2003::0002                                        

 key authentication cipher $c$3$+qsA4GoP0aSDprsQyjFcsijBFDr2wsISTg==           

 user-name-format without-domain                                               

#                                                                               

domain dm4                                                                     

 authentication portal radius-scheme rs4                                       

 authorization portal none                                                      

 accounting portal none                                                        

 access-limit disable                                                          

 state active                                                                   

 idle-cut enable 50 1024                                                       

 self-service-url disable                                                      

domain dm6                                                                      

 authentication portal radius-scheme rs6                                       

 authorization portal none                                                     

 accounting portal none                                                         

 access-limit disable                                                          

 state active                                                                  

 idle-cut enable 50 1024                                                       

 self-service-url disable                                                      

#                                                                              

 stp enable                                                                    

#                                                                               

wlan service-template 1 clear                                                  

 ssid service                                                                  

 bind WLAN-ESS 1                                                               

 service-template enable                                                       

#                                                                              

interface NULL0                                                                

#                                                                              

interface Vlan-interface1                                                      

 ipv6 address 2003::3/64                                                        

 ipv6 address FE80::4 link-local                                               

 ip address 192.168.100.163 255.255.255.0                                      

 vrrp vrid 2 virtual-ip 192.168.100.245                                        

 vrrp ipv6 vrid 2 virtual-ip FE80::40 link-local                               

 vrrp ipv6 vrid 2 virtual-ip 2003::100                                         

#                                                                               

interface Vlan-interface10                                                     

 ipv6 address 3010::2/96                                                       

 ip address 192.168.10.2 255.255.255.0                                          

#                                                                              

interface Vlan-interface100                                                    

 ipv6 address 3001::2/96                                                        

 ip address 192.168.1.2 255.255.255.0                                          

#                                                                              

interface Vlan-interface200                                                    

#                                                                               

interface Vlan-interface300                                                    

 ipv6 address 3003::2/96                                                       

 ipv6 address FE80::3 link-local                                               

 ip address 192.168.3.2 255.255.255.0                                          

 vrrp vrid 1 virtual-ip 192.168.3.100                                          

 vrrp ipv6 vrid 1 virtual-ip FE80::30 link-local                               

 vrrp ipv6 vrid 1 virtual-ip 3003::100                                         

 portal control-mode mac

 portal server officev4 method direct                                          

 portal server officev6 method direct                                          

 portal domain dm4                                                             

 portal domain ipv6 dm6                                                        

 portal backup-group 1                                                         

#                                                                              

interface GigabitEthernet1/0/1                                                 

 port link-type trunk                                                           

 port trunk permit vlan 1 100 300                                              

#                                                                              

interface GigabitEthernet1/0/2                                                  

 port link-type trunk                                                          

 port trunk permit vlan 1 100                                                  

#                                                                               

interface GigabitEthernet1/0/3                                                 

 port access vlan 10                                                           

#                                                                               

interface WLAN-ESS1                                                            

 port link-type hybrid                                                         

 undo port hybrid vlan 1                                                        

 port hybrid vlan 200 300 untagged                                             

 port hybrid pvid vlan 200                                                     

 mac-vlan enable                                                               

#                                                                               

wlan ap ap1 model WA2620E-AGN id 1                                             

 serial-id 21023529G007C000020                                                

 radio 1                                                                        

 radio 2                                                                       

  service-template 1 vlan-id 300                                               

  radio enable                                                                 

#                                                                              

 dhbk enable backup-type symmetric-path                                        

 dhbk vlan 10                                                                  

#                                                                              

return                                                                         

·     Switch 1的配置文件：

#

 stp enable

#                                                                              

·     Switch 2的配置文件：

 dhcp enable                                                                   

#                                                                               

 ipv6 dhcp server forbidden-address 3001::1 3001::4                            

 ipv6 dhcp server forbidden-address 3003::1 3003::4                            

#                                                                              

#                                                                               

vlan 1                                                                         

#                                                                              

vlan 100                                                                        

#                                                                              

vlan 200                                                                       

#                                                                               

vlan 300                                                                       

#                                                                              

 stp global enable                                                             

#                                                                              

dhcp server ip-pool 100                                                        

 network 192.168.1.0 mask 255.255.255.0                                        

#                                                                              

dhcp server ip-pool 300                                                        

 network 192.168.3.0 mask 255.255.255.0                                        

#                                                                              

ipv6 dhcp pool 1                                                               

 network 3001::/96                                                              

#                                                                              

ipv6 dhcp pool 2                                                               

 network 3003::/96                                                              

#                                                                              

ipv6 dhcp pool global                                                          

#                                                                               

interface NULL0                                                                

#                                                                              

interface Vlan-interface100                                                     

 ip address 192.168.1.3 255.255.255.0                                          

 ipv6 dhcp select server                                                       

 ipv6 dhcp server apply pool 1                                                 

 ipv6 address 3001::3/96                                                       

 ipv6 nd autoconfig managed-address-flag                                       

 ipv6 nd autoconfig other-flag                                                 

 undo ipv6 nd ra halt                                                           

#                                                                              

interface Vlan-interface300                                                    

 ip address 192.168.3.3 255.255.255.0                                          

 ipv6 dhcp select server                                                       

 ipv6 dhcp server apply pool 2                                                 

 ipv6 address 3003::3/96                                                       

 ipv6 nd autoconfig managed-address-flag                                       

 ipv6 nd autoconfig other-flag                                                 

 undo ipv6 nd ra halt                                                          

#                                                                              

interface GigabitEthernet1/0/1                                                 

 port link-type trunk                                                           

 port trunk permit vlan 1 100 300                                              

#                                                                              

interface GigabitEthernet1/0/2                                                  

 port access vlan 100                                                          

 poe enable                                                                    

#                                                                               

interface GigabitEthernet1/0/3                                                 

 port link-type trunk                                                          

 port trunk permit vlan 1 100 300                                               

 poe enable                                                                    

#                                                                              

return                                                                          

4  相关资料

·     《H3C无线控制器产品 配置指导》中的“WLAN配置指导”。

·     《H3C无线控制器产品 命令参考》中的“WLAN命令参考”。

·     《H3C无线控制器产品 配置指导》中的“安全配置指导”。

·     《H3C无线控制器产品 命令参考》中的“安全命令参考”。

·     《H3C无线控制器产品 配置指导》中的“二层技术配置指导”。

·     《H3C无线控制器产品 命令参考》中的“二层技术命令参考”。